首页技术中心>帕金斯柴油发动机3012喷油器的谈细参数与维修保养技术

帕金斯柴油发动机3012喷油器的谈细参数与维修保养技术

2016/5/10 13:57:40

Fuel injectors
燃料喷射器
1 Disconnect and remove the high-pressure pipes
1断开并拆下高压管道
and the spill pipes. For early engines, remove the
和泄漏管道。对于早期的发动机，删除
relevant rocker box cover, operation 12-4. Release
相关摇臂箱盖，操作12-4。释放
the connection for the leak-off fuel from the fuel
燃油从燃油中泄漏的连接
injector and remove it through the wall of the rocker
喷油器并将其拆下摇臂的壁
box. For new engines, remove the relevant pedestal
箱。对于新发动机，拆下相关底座
rocker cover, operation 12-1.
摇杆盖，操作12-1。
2 Release the cap screw of the clamp which retains
2松开保持夹持的盖螺钉
the fuel injector and withdraw the injector. A fuel
喷油器和喷油器的喷射。燃料
injector which is tight in the cylinder head may be
在气缸盖上的喷油器可能是
released by the use of the slide hammer, 21825 849
使用滑动锤释放，849 21825
(A1) and the adaptor, 21825 854 (A2).
（A1）和适配器，21825 854（A2）。
Caution: Ensure that the copper fuel injector sleeve
警告：确保铜燃油喷射套管
is not loosened in the cylinder head when the s lide
不松开气缸盖时的利得
hammer is used. If this occurs, refer to operation 12-
用锤子。如果发生这种情况，参考操作12—
1 Check that the sleeve of each injector is clean.
1检查每个喷油器的套是否干净。
2 If relevant, remove the connection for the leak-off
2如果有相关的话，删除连接泄漏
fuel from eac h fuel injector and fit carefully each fuel
从每个喷油器的燃油和适合仔细每个燃料
injector into its s leeve, with the threaded hole for the
喷油器成的堤防，与螺纹孔的
leak-off fuel toward the outer wall of the rocker box.
向摇杆箱外壁泄漏燃料。
Caution: If a Bosch fuel injec tor is to be fitted to an
注意：如果一个博世喷油器是安装在一个
early engine, instead of a CAV or an OMAP fuel
早期的引擎，而不是一个CAV或OMAP燃料
injector previously fitted, a new connection and a new
注射器先前安装，一个新的连接和一个新的
washer for the leak-off fuel must also be fitted
泄漏燃油的垫圈也必须安装
(assembly CV 17009/1).
（汇编1 / 17009）。
3 Fit the assembly of the metal cup and the rubber
3配合金属杯和橡胶的装配
seal against the head of each connection for the leak-
密封的每个连接的头的泄漏—
off fuel and fit a new copper washer onto the thread.
燃油，并将一个新的铜垫圈安装到螺纹上。
For early engines, insert each connection through
对于早期的发动机，插入每个连接通过
the openings in the outer walls of the rocker boxes
摇杆箱外壁上的开口
and fit the connection into its fuel injector, finger-tight.
并将其安装到燃油喷射器中，将其拧紧。
4 Fit each injector with its clamp and put a spherical
4配合每一个喷油器，用它的钳位，并把一个球
washer in its location in each clamp. Fit the cap
在每个夹具中的定位垫圈。安装盖
screws through the washers and clamps and tighten
通过垫圈和卡箍并拧紧
them to 60 Nm (42 lbf ft).
他们以60 nm（42磅英尺）。
5 For early engines, when all the cap screws of the
5为早期发动机，当所有的帽螺丝
clamps are tight, tighten the connections for leak-off
卡紧，拧紧连接泄漏
fuel to 27 Nm (20 lbf ft).
燃料27牛米（20磅英尺）。
6 Check that the joint face of each rocker box is
6检查各摇杆箱的接头面是否
clean. Fit a new joint for each rocker box cover and
清洁。为每个摇杆箱盖安装新接头
align correctly the bolt holes.
正确对齐螺栓孔。
7 Fit a new ’O’ ring to the groove at the top of each
7在每一个顶部安装一个新的'氧'环'
fuel injector. Fit carefully each rocker box cover. Fit
喷油器。小心地安装每一个摇杆箱盖。适合
the 8 bolts, with plain and spring washers, through the
8个螺栓，用平和弹簧垫圈，通过
bolt holes of each rocker box cover and tighten them
每个摇杆盖的螺栓孔，并拧紧
to 27 Nm (20 lbf ft). For new engines, fit a new ’O’
27牛米（20磅英尺）。对于新引擎，适合新的“哦”
ring around the groove which is near the top of each
环附近的槽，这是附近的顶部
fuel injector and fit the pedestal rocker cover,
喷油器和安装底座摇臂盖，
operation 12-21.
操作12-21。
8 If other work is to be completed, fit temporarily a
8如果其他工作要完成，暂时不适合
cover or a plug to each of the open connections of the
盖或插头各开连接的
fuel injectors.
燃料喷射器。
9 For all engines, if relevant, remove the cover from
9对于所有发动机，如果相关，从
the outlet connection for leak-off fuel of each fuel
每种燃料的泄漏燃料的出口连接
injector. Put a new copper washer on each side of the
喷油器。在每边上放一个新的铜垫圈
banjo connections and fit the pipes between the fuel
班卓琴的连接和配合，燃料管
injectors and the connection block for leak-off fuel.
喷油器和泄漏燃油的连接块。
Tighten securely each banjo connection bolt and
拧紧各连接螺栓和班卓琴的安全
each union nut.
每个工会的坚果。

10 Remove the covers or the plugs from the inlets of

the fuel injectors and, if relevant, from the unions of

the delivery valves of the fuel injection pump.

11 Put each high-pressure fuel pipe between its

delivery valv e and its fuel injector. Ensure that eac h

pipe lies naturally between its connections. Tighten

by hand each nut on to its relevant union. DO NOT

bend or distort a pipe to make it fit between its

connections. Tighten securely each nut to 45 Nm (33

lbf ft).

Note: Identification of each high-pressure fuel pipe is

made by the cylinder number which is stamped on the

union nut that is fitted on the fuel injector.

12 Fit new rubber dampers around each high-

pressure fuel pipe. Put the shrouds over the rubber

dampers and retain securely each shroud to its

induction manifold with bolts and spring washers.

To dismantle

1 Hold lightly the body (A1) of the fuel injector in a

vice with soft covers and release the cap nut (A2).

Withdraw the assembly of the nozzle (A3), together

with the adaptor plate (A4), the valve seat, the valve

spring and the adjus tment shims. Keep together, in

their own tray, all the components of each injector.

Caution: Each nozzle needle is ground to the body

of its own noz zle and it is not interchangeable with

any other nozzle.

To assemble

1 Hold lightly the body of the injector in a vice and

insert the correct adjustment shims followed by the

valve spring and the seat. Fit the adaptor plate

around the seat.

2 If the nozzle and the noz zle needle are not

assembled, dip the components in clean ISO 4113

test oil and slide the valve fully into its location in the

nozzle. Fit the assembly to the adaptor plate and fit

the cap nut. Tighten the cap nut to 80 Nm (59 lbf ft).

3 For the fuel injec tors of early engines, fit the

connection for leak-off fuel, complete with a new

copper washer, into the body of the fuel injector. Do

not tighten fully the connection during this operation.

帕金斯柴油发动机喷油器清洁和检查

喷嘴CVK 508清洁套装

1 Wash the components of each injector in clean ISO

4113 test oil and dry with compressed air. Soak the

nozzle assembly in a carbon solvent such as ’Maxan

774’ which can be obtained from Henkel Chemicals

Limited, Edgeware Road, London.

2 Use the cleaning kit CVK 508 (A,B,C,D and E) to

remove, from the nozzle and the nozzle needle, any

carbon which remains.

It is important that all carbon is removed from the

spray holes and that the correct size of wire from the

cleaning kit is used. The c ross-section of each wire

has a ’D’ shape and its size is measured across the

full diameter. Wires for the cleaning kit are available

in sets of five and can be supplied separately.

3 3 Fit the wire into its holder and ensure that the

protrusion is not more than 1,5 mm (0.0625 in). If the

protrusion is longer, there is a danger that the wire

may break in the hole. Insert the wire into each hole

and turn it to use it as a scraper, until the hole is clean.

Caution: Use only the tools supplied with the

cleaning kit to clean the assemblies of the nozzles. Do

not use any other device.

4 When all of the holes are clean, soak again each

nozzle in ’Maxan 774’, wash in clean water and dry

with compressed air and then dip in clean ISO 4113

test oil. If a device to flush the nozzles in a rev erse

direction is available, flush through each nozzle to

remove all particles that may still remain.

5 Use a magnifying lens to check the seats of each
5用放大镜检查每个座位的座位
nozzle needle for roughness, distortion, or other
喷嘴针的粗糙度，失真，或其他
damage. Check for worn holes in the nozzle and
损伤。检查喷嘴内的磨损孔
check also the seat of each nozzle for damage.
检查每个喷嘴的损坏位置。
Caution: If the faces of the nozzle needle or of the
警告：如果喷嘴针的面或
nozzle show signs that they have been affected by
喷嘴的迹象表明，他们已经受到影响
excessive temperature, both components must be
温度过高，两个部件都必须
renewed. DO NOT try to lap a nozzle needle to its
更新。不要试图将喷嘴针到它的
seat as they do not have the same angles.
因为他们没有相同的角度。
6 Dip the nozzle needle into clean ISO 4113 test oil
6将喷嘴针浸在4113个试验油中
and insert it into the bore of its nozzle. Slide the
并将其插入其喷嘴孔中。滑动
nozzle needle fully into its location. Hold almost
喷嘴针完全进入它的位置。拥有近
vertical the nozzle and withdraw approximately one
垂直的喷嘴和撤回约1
third of the length of the nozzle needle from the
第三的喷嘴针的长度从
nozzle. When it is released, the weight of the nozzle
喷嘴。当它被释放时，喷嘴的重量
needle should cause it to slide down on to its seat.
针应该使它滑到它的座位上。
7 If the nozzle needle is tight in the body of the
7如果喷嘴针在体内的
nozzle, it is permissible to lap the stem of the needle
喷嘴，它是允许的，以圈干的针
in the body of the nozzle. A special v ery smooth
在车身的喷嘴。一个特殊的非常光滑
compound is available for this purpose from the
化合物可用于此目的的
manufacturer of the fuel injectors.
燃油喷射器的制造商。
8 Inspect the faces between the body of the injector,
8检查喷油器本体之间的面，
the adaptor plate and the nozzle for signs of scratc hes
适配器板和喷嘴的划痕他标志
or of damage which could cause leakage under
或可能导致泄漏的损害
pressure.
压力。
9 Check the shims for damage and inspect the valve
9检查损坏的垫片和检查阀
spring for distortion, damage or corrosion.
弹簧变形，损坏或腐蚀。

帕金斯柴油发动机喷油器的调整设置和测试

1 Use a test rig such as a ’Hartridge Injecta-centre’ to
1使用试验台如“哈特里奇注射液中心”
set the fuel injectors. Ensure that the container of the
设置喷油器。确保容器的
test rig is filled with clean ISO 4113 test oil. Loosen
试验台用洁净的异4113试验油。松开
the vent screw and operate the manual lever until the
排气螺丝和操作手动杆，直到
flow of oil is free from bubbles. Tighten the vent screw
流动的石油是免费的泡沫。拧紧排气螺钉
and continue to operate the manual lever until the oil
并继续操作手动杆，直到油
which flows from the connection of the discharge side
从放电侧的连接流
is also free from bubbles.
也没有气泡。
Warning! When an injector is tested, the nozzle
警告！当喷油器测试时，喷嘴
must be away from the operator because the oil which
必须远离运营商，因为石油
is sprayed has enough force to pass through skin.
喷有足够的力量通过皮肤。
2 Fit the connection of the discharge side of the test
2安装在测试的放电侧的连接
rig to the inlet of the injector and tighten securely.
钻机到喷油器入口，并牢固地紧固。
Close the valve of the pressure gauge to prevent
关闭压力表的阀门以防止
damage to the pressure gauge and operate rapidly
损坏压力表和操作迅速
the manual pump to ex pel the air from the fuel
前像素从燃料空气手动泵
injector. Open the valve of the pressure gauge one
喷油器。打开压力表的阀门
quarter of a turn (90°), operate slowly the lever and
四分之一的转（90），操作缓慢的杠杆和
make a note of the pressure at which the pointer of
作一个说明，在该压力的指针
the pressure gauge moves suddenly to indicate that
压力表突然移动以指示
the nozzle needle has opened. Unless other
喷嘴针已打开。除非其他
information is given, the press ure should be 243 bar
信息是给定的，压力应该是243吧
(240 atmospheres) ± 5 bar.
（240个大气压）5巴。
3 If the pressure of the injection is incorrect, the fuel
3如果注射的压力不正确，燃料
injector must be dismantled and the shims must be
喷油器必须拆除垫片必须
suitably adjusted. To increase the pressure, fit extra
适当调整。增加压力，配合额外
shims; to reduce the pressure, remove some shims.
垫片；减少压力，消除一些垫片。
4 When the correct setting is obtained, dry the tip of
4当正确设置时，干燥
the nozzle and operate the pump slowly to raise the
喷嘴和泵运转缓慢地提高
pressure until the pointer of the pressure gauge
压力，直到压力表的指针
indicates 223 bar (220 atmospheres). Keep this
指示223栏（220个大气压）。保持这
pressure for 10 seconds and then inspect the tip of
压力为10秒，然后检查的尖端
the nozzle; a damp tip is acceptable but there should
喷嘴；潮湿的顶端是可以接受的，但应该有
be no drops of oil.
无油滴。
Caution: Do not overtighten the cap of the nozzle to
注意：不要过紧的喷嘴帽
try to correc t a leakage.
要正确的泄漏。