康明斯工程机械用KTA19-P525 P630发动机技术规格参数
最大额定功率kW(BHP)：392(525) @1800r/min
持续额定功率kW(BHP)：392(525) @1800r/min
整机数据
型式…………………………………………………………..………….….….四冲程、直列、六缸
进气方式………………………………………………………..…………..….废气涡轮增压，中冷
缸径—mm(in.)×冲程—mm(in.)…………………………..…….…....….…159×159（6.25×6.25）
排量—L(in3)……………………………………………………..…..……….….…….…..18.9(1150)
压缩比…………………………………………………………………….…….…..…………..14.5:1
干式净质量
KTA19-C600康明斯发动机（参考安装图207171）—kg(lb.)…………………..………….1693(3730)
KTA19-P600康明斯发动机（参考安装图3010154）—kg(lb.)…………………………….2615(5760)
湿式净质量
KTA19-C600康明斯发动机（参考安装图207171）—kg(lb.)………..………….………….1762(3880)
KTA19-P600康明斯发动机（参考安装图3010154）—kg(lb.)..…………………………….2769(6100)
质心至缸体前端的距离（仅康明斯发动机本身）—mm(in.)………………….……..……. ...…572 (22.5)
质心在曲轴中心线上方（仅康明斯发动机本身）—mm(in.)……………………..…..……....…..239(9.4)
运动零件相对于曲轴中心线的转动惯量（不包括飞轮）—kg·m2(lb.ft2)…....….……1.82(43.2)
发火顺序……………………………………………………..……………………..…..…1-5-3-6-2-4
康明斯发动机悬置安装
在缸体后端面处的最大允许弯矩—N·m(lb.ft)……………………………..……..…..1356(1000)
康明斯发动机绕转动轴心的颠覆惯量—kg·m2(lb.ft2)………………………..…….…...…...….79(1876)
排气系统
最大允许排气背压—kPa(in.Hg)…………………...………………………………….……..10(3.0)
标准容许的排气管直径—mm(in.)………………………………………………….…..…..127(5.0)
进气系统
带重型空滤器允许的最大进气阻力
干净滤芯—kPa(in.H2O)………….….………………………………..……....….….....3.74(15)
脏滤芯—kPa(in. H2O)…………….………………………………………………....…6.23(25)
带重型空滤器允许的最小容尘能力—gm·l/s(gm/CFM)…………………………..….…...53(25)
冷却系统
冷却水容量
仅康明斯发动机—L(U.S.quart)……………………………………………………..……………30(32)
带散热器[适用环境温度为37.8℃（100°F）] —L(U.S.quart)………………...…....112(118)
康明斯发动机外部最大冷却水阻力—kPa(PSI)………………………………...…………..…..…....35(5.0)
康明斯发动机曲轴中心线上方冷却水的最大静压—m(ft.)……………………….…………….…18.3(60)
散热器最大空气阻力—kPa(in.H2O)…..………………………………………....……..…..0.12(0.5)
未沸腾冷却水@90°F(32℃)在热交换器内的最小流量—L/min(U.S. GPM)…..….………208(55)
未沸腾冷却水在热交换器进口处的最大压力—kPa(PSI)…………………………………689(100)
标准节温器温度调节范围—℃(°F)….…………………….………………..……..82-93(180-200)
最大冷却水压力（除压力盖外）—kPa(PSI)………………………………….…………...241(35)
压力盖允许的最小压力—kPa(PSI)…………………………………………….…………..….50(7)
顶部水箱允许的最高温度—℃(°F)...…………..……………………….………………..100(212)
顶部水箱推荐的最低温度—℃(°F)….……………………………………….…………...71(160)
允许的最小补水速率—L/min(U.S.GPM)……………………………………….….….……18.9(5)
允许的最大首次补水时间—min……………………………………………….….…...….....……5
允许的最小冷却水膨胀体积占系统容积%……………………..……………….…….……....….5
允许的最大排气时间—min………………………………………………………………………25
允许的最小冷却液水位降低容积—L(U.S.quart) ………………….……….……..……12.3(13)
（水位降低容积必须大于首次加水时未注满的容积，且不包括膨胀体积）
润滑系统
机油压力
低怠速时—kPa(PSI)……………………………………………………...…….……….138(20)
额定转速时—kPa(PSI)…………………………………………..………….….380-517(55-75)
额定转速时的机油流量—L/min(U.S.GPM)…..………………………..……….…..………132(35)
允许的最高机油温度—℃(°F)………………………………….…….……….…………121(250)
最大机油消耗量—L/h(U.S.quart/h)…………………………..…………………….…….0.31(0.33)
机油旁通滤清器容量
螺旋筒型—L(U.S.gal)…………………………………………..………………..…….2.6(0.7)
可更换零件型—L(U.S.gal) …………………………………..…………………..…….11(2.9)
机油盘容量
高位—L(U.S.gal)………………………………………………………....………..…….38(10)
低位—L(U.S.gal)……………………………………………………………….……….32(8.5)
系统总容量（除旁通滤清器外）—L(U.S.gal)……………………….………...……..……47(12.5)
标准机油盘的倾斜角(选用件 OP4019 CE)
前俯角………………………………………………..…………………………...…..…..... 30°
前仰角…………………………………………………..…………………….…..……....…30°
燃油系统
额定功率和转速时的最大燃油消耗量—kg/h(lb/h)…………………….…….…..………. 83(182)
额定功率和转速时的最大供油量—kg/h(lb/hr)………………………...………….……...140(308)
至PT燃油泵允许的最大供油阻力
滤清器在清洁状态时—kPa(in.Hg)…………………………….………….……...…...13.3 (4)
滤清器在脏的状态时—kPa(in.Hg)……………………………………….….………...26.7(8)
允许的喷油器最大燃油回油阻
带单向阀—kPa(in.Hg)…………………………………………………….……..….…22(6.5)
不带单向阀—kPa(in.Hg)………………………………………………..….………....8.5(2.5)
允许的最小燃油箱通气能力—L/h（ft3/h）……….……...……………………….....…...425(15)
（在背压为8.4kPa（2.5in.Hg）或更低的背压时）
最高燃油入口温度°F（°C）…………………………..…………….………………….160(71)
电气系统
推荐的电瓶最小容量（在-18℃（0°F））冷透状态或以上时—V………………….……….24
康明斯发动机不带负荷
冷起动电流—CCA…………………………………..…………….…………………..…....900
再次起动时电流容量（最小）………………..……….…………………….………...…..320
康明斯发动机带传动系统
冷起动电流—CCA………..……………………………………….……………..…………900
再次起动时电流容量（最小）………………………………………………………….....320
起动电路允许的最大压降@100Vm……………………………………………..…….…….…0.2
性能数据
怠速—r/min……………………………………………………………….……………….….…625
最高空载转速—r/min……………………………………………………………………….... 2050
最大超速能力—r/min……………………………………………………………………….....2625
最低启动温度时的脱离扭矩（无辅助装置）—N·m(lb.ft)…………………………....
最低启动温度时的起动扭矩（无辅助装置）—N·m(lb.ft)…………………..…..........556(410)
离合器接合时的有效扭矩(800 r/min) —N·m(lb.ft)………………………...……........1207(890)
推荐的与液力变扭器和液力泵相匹配的最小失速转速—r/min……………………….……1600
曲轴止推轴承负荷极限
最大间隙负荷—N(lb)……………………………………………………….…….6700(1500)
最大连续负荷—N(lb)……………………………………………………...…….…3350(750)
最低冷起动温度（无辅助装置）—℃(°F).…………………………………….….…….-3 (27)
最低起动转速（无辅助装置）—r/min……….……………………..……………………...…..150
所有的数据均是基于康明斯发动机带燃油泵、水泵、机油泵、空滤器和消声器运转时获得的，但不包括交流发电机、空压机、风扇、选用设备和驱动件。所有的数据都是基于SAE J1349标准规定的条件——海拔90m（300ft.），大气压力100kPa（29.61in.Hg），进气温度25℃（77°F），水蒸汽压力1.0kPa（0.30in.Hg），使用标准No.2号柴油或符合ASTM D2的柴油。数据随时可能更改，恕不另行通知。
|
康明斯发动机性能参数 |
额定工况 |
连续工况 | ||||||||||||
|
最大功率点 |
最大扭矩点 |
最大功率点 |
最大扭矩点 | |||||||||||
|
康明斯发动机转速—r/min |
1800 |
1400 |
1800 |
1400 | ||||||||||
|
输出总功率—kW(HP) |
392(525) |
320(429) |
392(525) |
320(429) | ||||||||||
|
扭矩—N·m(lb.ft) |
2080(1534) |
2182(1609) |
2080(1534) |
2182(1609) | ||||||||||
|
燃油管路额定点压力—kPa(PSI) |
1456(211) |
827(120) |
1456(211) |
827(120) | ||||||||||
|
进气歧管压力—kPa(in.Hg) |
138(41) |
104(31) |
138(41) |
104(31) | ||||||||||
|
平均有效压力—kPa(PSI) |
1186 (172) |
1489(216) |
1186 (172) |
1489(216) | ||||||||||
|
活塞平均速度—m/s(ft/min) |
9.5(1875) |
7.4(1460) |
9.5(1875) |
|||||||||||
|
摩擦功率—kW(HP) |
55(74) |
36(48) |
55(74) |
|||||||||||
|
进气流量—L/s(CFM) |
666(1410) |
337(715) |
666(1410) |
337(715) | ||||||||||
|
排气流量(干式排气管)—L/s(CFM) |
1484(3144) |
1081(2291) |
1484(3144) |
1081(2291) | ||||||||||
|
排气温度(干式排气管)—℃(°F) |
460(860) |
533(992) |
460(860) |
533(992) | ||||||||||
|
对环境的散热量 干式排气管—kW(BTU/min) |
23.7(1351) |
38.5(2169) |
23.7(1351) |
38.5(2169) | ||||||||||
|
对冷却液的散热量 干式排气管kW(BTU/min) |
232(13210) |
192(10920) |
232(13210) |
192(10920) | ||||||||||
|
康明斯发动机冷却水流量—L/s(U.S.GPM) |
12.6(200) |
9.7(154) |
12.6(200) |
|||||||||||
|
|
Chongqing Cummins Engine Data Sheet |
ENGINE FAMILY |
D19 | |||||||||||
|
ENGINE MODEL |
KTA19-C/P630 | |||||||||||||
|
PERF. NO. |
CPL# |
4150 |
DATA SHEET NO. |
|||||||||||
|
CONFIGURATION |
D193077CX02 |
Page |
1 |
of |
2 |
|||||||||
MAXIMUM RATING kW(BHP) @ r/min 470 (630) @ 1800
CONTINUOUS RATING kW(BHP) @ r/min 447 (600) @ 1800
GENERAL ENGINE DATA
Type …………………………………………………………………………………………….. 4 Cycle;In-line;6 Cylinder
Aspiration ……………………………………………………………………………………… Turbocharged & Aftercooled
Bore - in.(mm) X Stroke - in.(mm) ……………………………………………………….. 6.25(159) X 6.25(159)
Displacement – cu in (litre) .....................................................................................…… 1150 (18.9)
Compression Ratio …………………………………………………………………………… 13.8:1
Dry Weight
Fan Hub to Flywheel Engine (Ref. Installation Diagram No. 207171 ) - lb.(kg) ..…. 3730 (1693)
Radiator Cooled Engine (Ref. Installation Diagram No. 3010154 ) - lb.(kg) ………. 5760 (2615)
Wet Weight
Fan Hub to Flywheel Engine (Ref. Installation Diagram No. 207171 ) - lb.(kg) …… 3880 (1762)
Radiator Cooled Engine (Ref. Installation Diagram No. 3010154 ) - lb.(kg) ………. 6100 (2769)
Center of Gravity from Front Face of Block (Engine Only) – in. (mm) ........................... 22.5(572)
Center of Gravity above Crankshaft Centerline (Engine Only) – in. (mm) ..................... 9.4(239)
Moment of Inertia of Rotating Components (Excluding Flywheel) – lb-ft 2 (kg m 2 ) ....... 43.2(1.82)
Firing Order ………………………………………………………………………………….... 1-5-3-6-2-4
ENGINE MOUNTING
Maximum Allowable Bending Moment at Rear Face of Block - lb.-ft. (N•m) ................. 1000(1356)
Moment of Inertia About Roll Axis of Complete Engine – lb-ft 2 (kg m 2 ) ...................…. 1876(79)
EXHAUST SYSTEM
Maximum Allowable Back Pressure – in.Hg (mm Hg) ................................................. 3.0(76)
Exhaust Pipe Size Normally Acceptable in.(mm) ......................................................... 5.0(127)
AIR INTAKE SYSTEM
Maximum Allowable Intake Air Restriction with Heavy Duty Air Cleaner
— Clean Element - in. H2O( mm H2O ) ...........................................................………... 15(381)
— Dirty Element - in. H2O( mm H2O ) .................................................………................ 25(635)
Minimum Allowable Dirt Holding Capacity with Heavy Duty Air Cleaner - g/cfm(g-L/s)... 25(53)
COOLING SYSTEM
Coolant Capacity - Engine Only - U.S. quart (litre) ........................................................ 32(30)
- With 100 °F (Option ) - U.S. quart (litre) ....................... .............................................. 118(112)
Maximum Coolant Friction Head External to Engine – PSI(kPa) ………………………… 5.0(35)
Maximum Static Head of Coolant Above Engine Crankshaft Centerline ft (m) .............. 60(18.3)
Maximum Air Restriction Across Radiator – in.H2O (mmH2O) …………………………. 0.5(13)
Standard (modulating) Thermostat Range - °F (°C) ..................................................... 180-200(82-93)
Maximum Coolant Pressure (Exclusive of Pressure Cap) – PSI (kPa) ………………… 35(241)
Minimum Allowable Pressure Cap –PSI (kPa) .............................................................. 7(50)
Maximum Allowable Top Tank Temperature -°F (°C) …………………………………….. 212(100)
Minimum Recommended Top Tank Temperature -°F (°C) ………………………………. 160(71)
Minimum Allowable Fill Rate –U.S.GPM(L/min) ............................................................ 5(18.9)
Maximum Allowable Initial Fill Time –min. ..................................................................... 5
Minimum Allowable Coolant Expansion Space – % of System Capacity ....................... 5
Maximum Allowable Deaeration Time – min. ................................................................ 25
Minimum Allowable Drawdown – U.S.quart(litre) ........................................................... 13(12.3)
(Drawdown Must Exceed the Volume Not Filled at Initial Fill & Must Not Include Expansion Space)
LUBRICATION SYSTEM
Normal Operating Oil Pressure Range @ Idle – PSI(kPa) .........…………………………. 20(138) Minimun
@ Rated Speed – PSI(kPa) ......... ...................... ...................... .................................... 45-70(310-483)
Oil Flow at Rated Speed – U.S.GPM (L/min) ………………………………………………. 35(132)
Maximum Allowable Oil Temperature - °F(°C) .........................................……………..... 250(121)
Maximum Allowable Oil Consumption – U.S.qt/hr(L/hr) …………………………………… 0.33(0.31)
Oil Pan Capacity (Option OP4020) High/Low - U.S. gal.(litre) …………………………… 10-8.5(38-32)
By-pass Filter Capacity – Spin-on Cartridge Type U.S.gal(litre) .................................… 0.70(2.6)
- Replaceable Element Type – U.S.gal(litre) ……………………………………………….. 2.9(11)
Angularity of Standard Oil Pan (Values stated are for intermittent operation only): OP4020
— Front Down degrees ........................................................................... ...................… 30
— Front Up degrees ............................................................................... ........…........… 30
— Side-to-Side degrees ................................................................... ......................… 30
FUEL SYSTEM
Maximum Fuel Consumption at Maximum Rated Output and Speed – lb/hr(kg/hr) …………………217 (99)
Maximum Fuel Flow on the Supply Side of the Fuel Pump –lb/hr(kg/hr) ......................………..…. 367(167)
Maximum Allowable Restriction to PT Fuel Pump –with Clean Fuel Filter –in. Hg(mm Hg) ……….. 4(102)
–with Dirty Fuel Filter –in. Hg(mm Hg) …………………………………………………………………… 8(203)
Maximum Allowable Injector Return Line Restriction— with check valves in. Hg(mm Hg) ……….. 6.5(165)
— less check valves in. Hg()mm Hg.....………………………………………………………………….. 2.5(63)
Minimum Allowable Fuel Tank Vent Capability ft.3/hr(litre/hr) ……………………………………….. 15(425)
(With 2.5 in.Hg(63 mmHg) or Less Back Pressure
Maximum Fuel Inlet Temperature °F(°C)......................................................................................... 160(71)
CRANKING SYSTEM
Minimum Recommended Battery Capacity - Cold Soak at –18 °C (0 °F) or Above 24 Volt
— Engine Only (De-clutched Load) - Cold Cranking Amperes – CCA ............................... ............ 900
- Reserve Capacity – CCA ...................... .................................... ..................................... ............. 320
— Engine Only Connected Drive Train - Cold Cranking Amperes – CCA .......... ............................ 900
- Reserve Capacity – CCA ............................. .................................... ............................................ 320
Maximum Starting Circuit Voltage Drop @100 Amperes Volts .................................................... . 0.2
PERFORMANCE DATA
Minimum Engine Speed –RPM ....................................................................................................... 725
Maximum No-Load Governed Speed –RPM ……………………………………………………………. 2100
Maximum Overspeed Capability –RPM .......................................................................................... 2625
Breakaway Torque at Minimum Unaided Start Temperature –lb-ft(N•m) …………………………….
Cranking Torque at Minimum Unaided Start Temperature –lb-ft(N•m) ………………………………. 410(556)
Torque Available at Clutch Engagement (800 RPM) –lb-ft(N•m) …………………………………….. 890(1207)
Minimum Recommended Combined Converter and Hydraulic Stall Speed –RPM ......................... 1600
Crankshaft Thrust Bearing Load Limit
— Maximum Intermittent lb.(N)..................................................................………………………….. 1500(6700)
— Maximum Continuous lb.(N)..................................................................………………………….. 750(3350)
Minimum Ambient Temperature for Unaided Cold Start °F(°C) ………………………………………. 27(-3)
Minimum Cranking Speed Required for Unaided Cold Start –RPM …………………………………. 150
All data is based on: the engine operating with fuel system, water pump, lubricating oil pump, air cleaner, and muffler; not included are alternator,
compressor, fan, optional equipment and driven components. Data represents gross engine performance capabilities obtained and corrected in
accordance with SAE J1995 conditions of 100 kPa (29.61 in. Hg) barometric pressure [90 m (300 ft.) altitude], 25°C (77°F) inlet air temperature, and 1 kPa (0.30 in. Hg) water vapor pressure with No. 2 diesel fuel or a fuel corresponding to ASTM D2. All data is subject to change without notice.
- Maximum Rating - Continuous Rating
FULL PEAK FULL PEAK
POWER TORQUE POWER TORQUE
Engine Speed –RPM ......................................................... 1800 1400 1800 1400
Gross Power Output –BHP (kW) .......................................... 630(470) 530(395) 600(447) 506(378)
Torque lb.-ft.(N•m)............................................................. 1838(2492) 1990(2698) 1751(2374) 1900(2576)
Norminal Rail Pressure –PSI(kPa) ………………………………… 156(1075) 120(827) 145(999)
Intake Manifold Pressure in. Hg(kPa) …...................................... 56(189) 48(162) 53(180)
Brake Mean Effective Pressure –PSI (kPa) ………………………. 241(1661) 261(1799) 230(1582)
Piston Speed –ft/min (m/s) …………………………………………. 1875(9.5) 1460(7.4) 1875(9.5)
Motoring Friction Horsepower –HP (kW) ...................................... 74(55) 48(36) 74(55)
Intake Air Flow –CFM (L/s) .......................................................... 1434(677) 1044(492) 1389(655)
Exhaust Gas Flow (Dry Manifold) –CFM(L/s) ............................... 3144(1484) 2291(1081) 3040(1435)
Exhaust Gas Temperature - Dry Manifold °F(°C).......................... 860(460) 992(533) 856(458)
Heat Rejection-to-Ambient (Dry Manifold) —BTU/min(kW)........... 1351(23.7) 2169(38.5) 1229(21.7)
Heat Rejection-to-Coolant (Dry Manifold) —BTU/min(kW)........... 13210(232) 10920(192) 12626(222)
Engine Coolant Flow –U.S.GPM(L/s) ........................................... 200(12.6) 154(9.7) 200(12.6)
This Rating is a special for Taiwan Flood Pump Drive Application
All Data is Subject to Change without Notice KTA19-P630
Chongqing Cummins Engine Company Ltd.
Lieshimu Shapingba
Chongqing 400031
2003/5/22 CCEC
400-100-8969 15088860848
0574-26871589 15267810868
0574-26886646 15706865167
0574-26871569 18658287286
Deutsch
Espaol
Franais
Italiano
Português
日本
韩国
阿拉伯
български
hrvatski
esky
Dansk
Nederlands
suomi
Ελληνικ
印度
norsk
Polski
Roman
русский
Svenska
中文(简)